Tile Magic Flexi Grip

TILE MAGIC ADHESIVE – FLEXI GRIPTECHNICAL DATA SHEET

Flexi Grip Tile AdhesiveTILE MAGIC ADHESIVE – FLEXI GRIP is a grey rapid setting high strength cement-base tile adhesive for fixing POROUS and NON POROUS and for tiling DIRECTLY ONTO SMOOTH, DENSE SUBSTRATES TILE on TILE TECHNOLOGY. Suitable for interior and exterior application.

TILE MAGIC ADHESIVE – FLEXI GRIP is a pre-mixed precise blend of hydraulic cements, shrinkage compensation chemicals and fillers.  The product can be applied at varying thickness.

 

 TECHNICAL DATA
   With Water  With Bond
 Mix Ratio  20kg / 5 ℓ  20kg / 5 ℓ
 Open Time  Approx. 25 Minutes at 23 oC at 50% humidity  Approx. 25 Minutes at 23 oC at 50% humidity
 Correction Time  Approx. 30 Minutes at 23 oC at 50% humidity  Approx. 30 Minutes at 23 oC at 50% humidity
 Application Temperature  Approx. 10 to 35 oC  Approx. 10 to 30 oC
 Operating Temperature  0 to 100 oC  0 to 100 oC
 Pot Life  Approx. 90 minutes at 23 oC  Approx. 90 minutes at 23 oC
 Flash Point  Nil  Nil
 Final Set  12 hours  12 hours
 Flexibility  Very Good  Excellent
 Resistance to damp  Very Good  Excellent
 Tensile Adhesive Strength  28 Days  28 Days
 Storage Life  12 Months when stored in dry conditions  12 Months when stored in dry conditions

TILE MAGIC FLEXI GRIP is manufactured in accordance with the following international specifications:

BRAZILIAN STANDARD: ABNTNBR 14081 | EUROPEAN STANDARD: EN 12004 and EN 1348

SURFACE PREPARATION

  • New floor and wall surfaces must be allowed to cure for the minimum periods as tabled below to ensure that movement due to shrinkage does not affect the tiling.
    • New Concrete – 6 weeks
    • New Plaster – 2 weeks
    • New Screed – 4 weeks
    • New Render – 2 weeks
  • The substrate must have a moisture content of 5% or less before tiling commenced.
  • Ensure that the surface is clean, dry and free of all traces of laitance and contamination such as loose particles, oil, dust, waxes, bitumen, paint, grease, weak cement screeds, weak renders, sealing compounds, previous adhesives etc.
  • Enamel and PVA painted surfaces, gypsum, bitumen and existing tiles that are not soundly bedded, vinyl and novilon must be removed. Approximately 80% of the surface must be chipped before applying the adhesive or primed with a mixture of TILE MAGIC PRIMER mixed with TILE MAGIC GOLDEN FAST SET to form a slurry. Apply with a builders block brush, allow to dry prior to applying the tile adhesive. (1-part Tile Magic Primer to 2 parts Golden Fast Set tile adhesive or 1.5 parts ordinary Portland cement (by volume).
  • Organic growth must be killed and removed using an effective fungicide.
  • Dense, smooth off shutter and power floated concrete and smooth plastered walls should be acid etched to obtain a sound keying mechanism.
  • Rinse surface thoroughly with clean water after etching.

DIRECTIONS FOR USE

MIXING

  • Add approximately 4 parts of tile adhesive to 1 part clean water or gradually mix 20kg tile adhesive to 5 ℓ of clean water.
  • Mix to a creamy consistency, allow to stand for 5 – 10 minutes, stirring again WITHOUT mixing more water and use immediately. Pot life after mixing is approximately 90 minutes.
  • NB: Never add more liquid to a mix which has been left standing for too long, as this will compromise the integrity of the adhesive.
  • For wet conditions or where heavy duty strength is required, replace water in the mix with TILE MAGIC TILE PRIMER in ratio of 20kg TILE MAGIC ADHESIVE to 5 ℓ of TILE MAGIC PRIMER.

APPLICATION

  • Ensure that the tiles are dry and the backs are free of dust and contaminants.
  • Spread adhesive with a notched trowel to a minimum bed thickness of 3mm on walls and 6mm on floors. Bed tiles firmly into wet adhesive using a rubber mallet. The entire back surface of the tiles must have full contact with the adhesive.
  • NEVER USE THE SPOT METHOD WHEN APPLYING THE ADHESIVE.
  • DO NOT BUTT JOINT TILES.
  • Bed tiles firmly using a Rubber mallet. When tiling floors or exterior walls ensure that the tile is in full contact with the adhesive.
  • Do not tile over structural, expansion or cold joints in the background. These joints must be extended through the various layers to the surface.
  • Remove all excess adhesive from the grouting joints before drying has occurred.
  • Ensure that the panel movement joints and perimeter joints are raked out and all adhesive residues removed before the adhesive dries.
  • Always leave grout joints between tiles; at least 2mm wide between ceramic wall tiles and 5mm wide between ceramic floor tiles.
  • It’s important to allow for differential movement in all tiling applications so the inclusion of Tile Panel Movement joints, Structural Movement joints and Perimeter joints is essential.

MOVEMENT JOINTS

  • Tile panel Movement joints should be located in both directions at maximum 5 meter centres for interior surface bed and wall applications, and maximum 3 meter centres for suspended applications and exterior applications.
  • Movement joints should also be located around the perimeter of all floors, in all horizontal and vertical corners, against obstructions fixed to the structural background and over all discontinuities in building materials, e.g. at interfaces of concrete and brickwork. In addition, movement joints should be located around any fixtures protruding through the tiled surface such as columns or stairs. The joints should be at least 5mm wide and extend through the adhesive and tile layers. All construction / cold joints and structural joints in the background must be extended through the adhesive and tile layers to the surface in the form of tile panel movement joints. With regards to structural joints, the full width of the structural joints must be respected and extended through the adhesive and tile layers to the surface.

GROUTING

  • Allow at least 12 hours before grouting commences, depending on atmospheric conditions.
  • Ensure that the joints are free of tile adhesive residue or any other foreign or loose particles.
  • DO NOT GROUT WITH NEAT CEMENT.

COVERAGE

A 20kg bag of wall and floor TILE MAGIC FLEXI GRIP ADHESIVE will cover approximately 6 m2 using 6mm x 6mm notched WALL TROWEL and 4 m2 using a 10mm x 10mm notched FLOOR TROWEL. (Actual coverage will be determined by site conditions, workmanship, etc.)

PRECAUTION

  • Ensure that the above instructions are adhered to al all times and not adulterate the product in any way as this could cause failure.
  • People with sensitive skin should wear rubber gloves. Seek medical attention if irritation or discomfort persists after contamination with adhesive. In case of eye contact, wash well with clean water and obtain medical assistance if discomfort persists.
  • Do not ingest.
  • Do not discharge into drains.
  • Keep away from children and pets.
  • Clean all equipment immediately after use with potable water.
  • Structural movement joints must be respected and joints must be provided for.

PACKAGING

TILE MAGIC FLEXI GRIP ADHESIVE is supplied in 20kg double lined moisture resistant bag

GUARANTEE

TILE MAGIC FLEXI GRIP is guaranteed when used in accordance with correct product application and instruction procedures.

Download/Print this Document